The Bedini SSG is one types of magnetic motor generators based on zero point Keyword-Component: Bedini SSG circuit operation; Bifilar. Below is the circuit I have been using. This is the basic Bedini SSG (Simplified School Girl) motor. The only difference in my circuit is I am using a 2N I have been researching on Bedini circuits, mostly the simple one (SSG located here ). I worked out in many.
|Published (Last):||27 March 2006|
|PDF File Size:||13.91 Mb|
|ePub File Size:||8.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Last edited by Tachyon Catcher; at This book is something you must get if you are to build the correct working machine. Our status and that of any identified contributors as the authors of material on vircuit site must always be acknowledged. It will shorten the battery’s life considerably if this is habitually done. In the circuit shown above I simply added the diode at the point shown in red.
John Bedini Simplified School Girl basic plans
It was stuck for long enough to heat the coil up far enough to brown the tape holding it together, and it will no longer stay running for very long. Or smaller for smaller setups. Copyright – energyscienceforum.
I would really like to see this forum transform from a group of Bedini enthusiasts to a fast-growing consensus of researchers with documented proof of the legitimacy of this technology. HI, this is first time to make a comment.
Inkscape DXF output for Lasercut.
Thanks for the comments so far guys! By careful coil design or the addition of a potentiometer, it is arranged that the motor is close to self-oscillation.
Single coil Bedini motor charging 4 batteries w no current increase
Instructions Medium Resolution Video of the Presentation for high speed: The amount of power you can take out will reduce significantly the first few times until it stabilizes. Culver City Industrial Hardware It’s best to have an arrangement that you can shut off quickly, or even use a circuit breaker to prevent a dead short if the transistor fails to oscillate. A poor Man Reedswitch can be made with 2 cutted Razorblades, or one Blade and a copper contact.
The red wire shows the wire leading to a new diode and charge battery set. Here are the steps to explain what is happening. You want ciircuit take the voltage down to a predetermined voltage level which you will be watching precisely say Strength of magnet is very low, just to activate the reed switch.
We are going to call this, for future simplicity’s sake, the load termination point. Hook it to the same battery you are running the motor on. Does the reed switch last or have you had cidcuit go bad after a while? Apparently the best possible output for this setup is using only the reed switch without the transistor but it has to be a high current one. Multiply the volts times amps to get the watts. Find all posts by alek. I’ll tell you that in some of my setups, one spike per pulse worked the best, others liked multiple spikes per pulse.
I would really like to see some direction on this forum, so others are circuti to experiment! Circuit is same as SSG one, http: My understanding is that you require less windings with a stronger magnetic field in the center.
Bedini SSG Circuit
Additional construction details are found here: Shoutbox provided by vBShout v6. Further clarifying remarks between these [ ] brackets may be added later.
Also, if the coil is not pulsed while the magnet passes over, there are inductive currents that result. If you want to do multiple setups that’s fine, just report each separately and we’ll log the data accordingly.
Arduino as ATtiny programmer. These documents contain all the information needed for building and testing the SSG Energizer.
Adding a network printer in Ubuntu. Materials List The following is a list of materials that may be necessary to replicate the Bedini School Girl circuit and motor as presented in this guide. The other day I was experimenting with capacitors and LEDs in series with the output charging battery and got some interesting results.
Bedini SSG – Science DIY
Thinker with the components, experiment with the magnets, coil, batteries, transistor etc. Thus, in one direction of current flow through the base-emitter of the transistor switch, the transistor is turned on momentarily to connect the battery 18 across the coil Originally Posted by geotron This looks to be producing energy at a substantial rate, in the range of kHz.
I’ve just recently become familiar with the ssg, but don’t really understand it either? By the way do you know bevini web site which shows more detail step by step to make SSG motor? Hope that everything comes to normal there. Try also an auto parts store.