(This Information Sheet is NOT an AGMA Standard). Inspection Practices — Part 1 : Cylindrical Gears — Tangential American Measurements Gear AGMA mental Tables for AGMA /A02,. Accuracy Classification System— Tangential. Measurement Tolerance Tables for Cylindrical. Gears, was published . AGMA A02 Inspection Practices – Part 1: Cylindrical Gears – Tangential Measurements Provides a code of practice dealing with inspection relevant to.

Author: Nejind Mojora
Country: Botswana
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 6 October 2006
Pages: 145
PDF File Size: 18.60 Mb
ePub File Size: 5.32 Mb
ISBN: 289-6-41425-620-6
Downloads: 92773
Price: Free* [*Free Regsitration Required]
Uploader: Ararg

Please first log in with a verified email before subscribing to alerts. The key to a proper fit for keyways. In addition to the actual helix traces, numerical values for the different helix parameters may be shown on the printed output. As the voice of the U. Heat treating low alloy PM steels October 15, We have no amendments or corrections for this standard. Monday, December 31, Line 2 represents the actual trace of the tooth and the deviation of the actual helix from the nominal.

Item Detail – AGMA A05

See Figure 1 for afma explanation of what they represent. If the gear designer specifies crowning, end relief, or taper, line 1 would be modified accordingly. The benefits of converting to helical gearing.

If the part is a helical gear, the inspection equipment rotates the part as the probe moves axially to generate 9155 nominal helix. A primer on backlash, its purpose in gear designs.

The measuring probe is positioned against a tooth flank at one end of the face width at the tolerance diameter dT, which is one module below the tooth tips. Unless otherwise specified, the maximum total helix deviation Fb of all the measured right flanks is used to determine the helix quality level of the right flanks.


Tooth Tips: Gear Accuracy Charts Pt. 2 | Gear Solutions Magazine Your Resource to the Gear Industry

Understanding Carburizing August 11, Subscription pricing is determined by: Log in to leave a atma. It is a complete revision in order to be more compatible with ISO. If the part is a spur gear, the part does not rotate.

Log into your account. Helix measurements determine the accuracy of the teeth along their length. Standards Subsctiption may be the perfect solution. The tooth at space 1 has the largest total 951 deviation Fb of 0. We have no document history for this standard. Gear Accuracy Charts Pt. If the document is revised or amended, you will be notified by email.

The same procedure is used to classify the quality level of the left flanks.

The accuracy grade numbering system has been reversed, so that the smallest number now represents the most accurate grade. Your Alert Profile lists the documents that will be monitored.

Heat Treatment of Steel Gears July 15, Normally both flanks of three to four teeth equally spaced around the gear are measured and the results magnified and charted on a strip chart or printed out. This standard is not included in any packages. Add to Alert PDF. Proceed to Checkout Continue Shopping.

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Figure 1 is a copy of Figure 24 of AGMA A02 and is a sketch of a typical helix measurement trace for one flank of a tooth.


If the measured helix were perfect without any intentional modifications, the trace would be a straight line as shown at line 1 on the chart. Provides a code of practice dealing with inspection relevant to tangential element and composite deviations of cylindrical involute gears measurements referred to single flank contact. Converting to linear motion using rack and pinion.

Continuous Cooling Transformation Diagrams. Site Safety October 1, Site Safety June 1, This standard is also available to be included in Standards Subscriptions. Surface Engineering of Steels: You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. With most inspection machines, the probe moves along the tooth parallel to the axis of the part. Already Subscribed to this document.

Lb is the helix evaluation range used to classify the helix quality and is the length of the face width reduced slightly at each end.

Please first verify your email before subscribing sgma alerts. The scale in the vertical direction has been expanded more than normal to help clarify the various items on the chart.

Tooth Tips: Gear Accuracy Charts Pt. 2

Tolerances associated with gears. Figure 2 is an example of actual helix measurements of the right flanks of a tooth gear with a 4. Need more than one copy?